Chevrolet Volt gen 2 2016–2019 Transmission Reliability Under Real Ownership
Overview
The 2016–2019 Chevrolet Volt is a weird one. Good weird when it’s right. Expensive weird when it isn’t.
This car does not use a normal stepped automatic. The whole front drive setup is GM’s 5ET50 electric drive unit, an integrated front-wheel-drive transaxle that packs two electric motors, planetary gearing, clutch elements, and the final drive into one case. So when people ask about “Chevrolet Volt transmission problems,” they’re usually expecting the old-school stuff—slipping, banging shifts, burnt fluid, lunching gears. That’s not how this platform usually fails.
In my experience, the ugly stuff on these cars shows up as hybrid propulsion warnings, no-start events, weird code clusters, or noises that change under regenerative braking. Different animal. Same pain in the wallet.
GM issued a stack of service publications that tell the story pretty clearly. The big ones are PIC6244C, 19-NA-211, 18-NA-186, 19-NA-103, and 19-NA-067. Those documents matter because they show where the field failures were showing up on real cars, not in marketing brochures, not in owner fantasy-land, and not from somebody guessing off a forum post after one bad Saturday.
I do not see a transmission-specific NHTSA safety recall for the 2016–2019 Volt drive unit in the official material reviewed. That does not mean the tranny is flawless. It means the regulatory trail is more bulletin-driven than recall-driven on this generation. That distinction matters if you’re shopping one, already own one, or you’re staring at a repair estimate that looks ridiculous for a compact hatchback.
And that’s really the point with this platform. Most of them are fine. Some are not. When they go bad, the repair path can jump from “probably a sensor thing” to “you need a drive unit” way too fast.
Which Transmissions It Uses
There was one transmission family used in the US-market second-generation Volt. One. No hidden option, no better AWD version, no different unit for upper trims.
| Transmission Model Code | Gear Count | Drive Layout | Engine Pairing | Production Years | Notes |
|---|---|---|---|---|---|
| 5ET50 (RPO MKV) | No published conventional fixed gear count; GM service information identifies five operating modes | FWD | 1.5L range-extender gasoline engine with dual electric motors | 2016–2019 | No verified alternative transmissions used for this generation |
The 5ET50 is better described as an electric variable transaxle than a regular automatic. That’s why generic advice about automatic transmission maintenance only gets you so far here. There’s no torque converter to fail. No normal shift feel to judge it by. No transfer case. No rear differential. No driveshaft running to the back because every second-gen Volt sold here is front-wheel drive.
GM also published guidance telling technicians that some engine speed flare is normal because the system moves through different operating modes. I’ve had people swear the tranny was slipping when what they were feeling was normal system behavior. Then I’ve had other cars come in where the owner ignored a real problem because someone told them “they all do that.” That’s where people get burned.
With this setup, you don’t guess. You scan it. You road test it. You look at the code history and the way the noise shows up under load, under regen, cold, hot, all of it.
Main Failure Patterns
The first real problem area is the internal motor-position fault path covered by GM bulletin 19-NA-211. This one hits 2016–2018 cars and it can show up as a no-start or a loss-of-propulsion condition with DTCs P0A45 and P1B04. If you’re not familiar with these cars, it’s easy to think the issue is somewhere outside the transmission. A lot of times it isn’t. The fault can be inside the 5ET50 itself.
This is one of those messy failures where the symptom doesn’t tell the whole story. Car won’t move. Hybrid warning on. Customer says it “just died.” Could be internal bearing damage. Could be harness trouble. Same complaint, very different repair bill.
GM’s own repair logic in 19-NA-211 is pretty revealing. The technician is told to inspect for rotor-bearing-cage damage first. If the bearing cage has come apart, now you’re dealing with contamination, shavings, internal damage, and a much uglier path. If the bearing cage is still intact, the repair may stop at the internal transmission wiring harness. Big difference there. Massive difference, really.
I’ve seen dozens of driveline complaints where the owner was hoping for a cheap external fix and the tranny had already started making metal. Once that happens, all the optimism in the world doesn’t help. Metal inside one of these units is bad news because the 5ET50 is so integrated. It is not the kind of setup where you just slap on a band-aid fix and call it a day.
The next official pattern is in bulletin 18-NA-186. Same basic pain, different code path. Here GM covers no-start or loss of propulsion with P0A3F and P1B03 and points the technician toward the internal transmission wiring harness. The bulletin describes backed-out terminals, poor crimps, corrosion, and high resistance. I like that bulletin because it is specific. It doesn’t dance around the issue. The harness can be the failure point. Period.
That matters for used buyers because this generation doesn’t always fail like a mechanical box with obvious chatter or slip. Sometimes the failure is electrical, buried inside the transmission assembly, and still expensive enough to ruin your week.
Then there’s the internal noise side of the story. This is where people get nervous, and for good reason. Earlier GM guidance tied whistle, whine, or scrape noises from the left side of the transaxle area to internal bearing-cage damage. In real service bays, a Volt that starts making a rotational whine that changes with regenerative braking gets my attention fast. That isn’t a “watch it and see” complaint on a high-mileage unit. That’s a “figure out where the noise is coming from before this thing grenades” complaint.
The code-cluster issue in PIC6244C is another one owners need to know about. GM states that if P1AEE, P1AEF, P1AF0, P1AF2, and P1E22 are all present together, the problem points to an internal drive-unit concern and the repair direction is transmission replacement. Not fluid. Not an external harness wiggle test. Replacement.
That one is huge because it changes the economics right away. Once you get into that exact cluster, you’re not talking about a maybe. You’re talking about a documented threshold where GM’s own diagnostic path says the internal drive unit is the problem.
There’s also a front driveline issue that gets confused with transmission failure all the time. Bulletin 19-NA-103 covers an intermittent click from the front axle area. GM’s fix is to remove and discard the anti-click washer and inspect the wheel speed sensor for damage. Simple on paper. Easy to misread in the real world.
I’ve had customers come in convinced the tranny was coming apart because they heard a click on takeoff, a click backing up, or a click when torque reversed. Sometimes it really is just the axle-interface issue from that bulletin. Annoying, yes. Expensive internal transaxle failure, no.
And then there’s bulletin 19-NA-067, which is the sort of thing you only appreciate after you’ve chased enough noises on hybrids. GM ties a low-pitch moan or whine during regenerative braking, Low mode, or paddle regen to debris trapped in the rear powertrain mount area. That noise can sound like a driveline problem. It can fool people. Shops too. Clean out the debris and the noise is gone. No internal tranny repair needed.
So the main failure patterns on this generation break down like this: internal motor-position fault path, internal harness problems, internal bearing-related noise and damage, axle click issues, and a noise pattern that can send you after the wrong part if you don’t know the bulletin history.

Typical Repair Costs
Now the part nobody likes.
Repair costs on the second-gen Volt swing hard depending on what the diagnosis lands on. A front axle click and an internal drive-unit failure may sound related to the customer. They are not related to the invoice. Not even close.
| Repair Scenario | Typical Cost Range | Cost Basis | What Usually Drives the Total |
|---|---|---|---|
| Front axle click correction under bulletin 19-NA-103 | $150–$450 USD | Service Bay Benchmark | Diagnosis time, axle-end inspection, wheel speed sensor replacement if damaged |
| Rear powertrain mount debris/noise correction under 19-NA-067 | $100–$250 USD | Service Bay Benchmark | Inspection time and confirmation that the noise is not internal to the drive unit |
| Internal transmission wiring harness repair tied to 18-NA-186 or 19-NA-211 | $1,200–$2,400 USD | Industry Estimate | Hybrid diagnosis time, transaxle access, internal component labor |
| Internal motor-related repair after bearing-cage damage is found | $3,000–$5,500 USD | Industry Estimate | Internal contamination, motor-related parts, case cleaning, labor intensity |
| Complete 5ET50 drive-unit replacement | $6,000–$11,000 USD | Service Bay Benchmark | Assembly cost, parts availability, programming, dealer labor rate |
That spread is why diagnosis matters so much on this car. I’ve seen owners panic over a front-end click that turned out to be pretty manageable. I’ve also seen people try to cheap out on a real hybrid driveline diagnosis, keep driving it, then end up with a bigger bill after internal damage got worse.
The complete drive-unit replacement number is the one that changes the conversation. On an older Volt, that kind of bill can get real close to the value of the car. You need to be honest about that. If the vehicle is worth, say, compact-hatchback money and the transaxle wants luxury-car repair money, that matters.
It also changes the math for pre-purchase inspections. Spending money on a good scan and a competent hybrid road test is cheap compared to buying a car with unresolved internal codes and learning about it later.
Best and Worst Years
I’m careful with “best year” and “worst year” claims because people love oversimplified answers. Reality is messier. All 2016–2019 Volt models in the US use the same 5ET50 family, but the official bulletin trail puts the core internal harness and motor-position fault activity on 2016–2018 vehicles. That doesn’t make every early car bad. It does mean I look harder at them.
| Model Year | Drive Unit | Risk Profile | Why |
|---|---|---|---|
| 2016 | 5ET50 | Higher relative risk within the generation | Earliest production year, exposed to later bulletins for internal harness and drive-motor position faults |
| 2017 | 5ET50 | Higher relative risk within the generation | Still within the core bulletin years for internal no-start and propulsion-loss fault paths |
| 2018 | 5ET50 | Moderate risk | Still covered by major internal fault bulletins, but later service updates exist |
| 2019 | 5ET50 | Moderate to lower relative risk within this generation | Later production, no verified alternative transmission, front axle click issue still relevant |
In my experience, I’d rather buy a clean later car with records than an early one with mystery history and a seller who says “these all make weird noises.” No. They don’t all make the same weird noises, and the kind of weird matters.
I’ve seen plenty of solid 2016 and 2017 cars too. The difference is paperwork, code history, and whether somebody already threw parts at it instead of diagnosing it properly. A documented early car can still be a smarter buy than a neglected later car. Happens all the time.
Warning Signs & Early Detection
This platform tells on itself, but you need to listen the right way.
The first thing I care about is module-level scan data. Not just a cheap code reader. Not just a parts-store scan. You need a real scan that can see the hybrid and transmission-related modules. If the car has a history of propulsion warnings, no-start events, or stored codes tied to the drive unit, that’s where the story starts.
The second thing is noise behavior. A rotational whine, whistle, or scrape that gets stronger under regenerative braking is a bad sign on one of these. I’m not saying every regen-related noise means the tranny is cooked. I am saying you don’t brush it off.
The third thing is seller language. I pay attention to that. “It only did it once.” “Probably a bad sensor.” “Hybrid message came on but it reset.” “Shop said it might need software.” Those phrases can mean nothing. They can also mean somebody is trying to unload a ticking time bomb before the next failure event turns into a huge estimate.
The fourth thing is the front-end click on torque reversal. This one needs context. A click on launch, braking, or reverse engagement can line up with the anti-click washer issue in 19-NA-103. That’s a lot less scary than an internal 5ET50 fault, but you still inspect it. You don’t assume. You verify whether the wheel speed sensor got hit too, because that adds to the repair and can trigger extra warning lights.
During a proper pre-purchase inspection, I want a full module scan, a road test that includes regenerative deceleration, a cold start and warm drive if possible, and documentation of any prior hybrid driveline work. If the car already had a drive unit swapped, I want the invoice. I want the date. I want the mileage. I want to know whether the repair was done right or just slapped on so the car could be sold.
And one more thing. If the seller refuses a scan, leave. That’s it. Don’t romanticize it.
When to Walk Away
I would walk away from a second-gen Volt if it shows the exact code cluster GM ties to internal drive-unit replacement in PIC6244C and there’s no warranty help left on the table. At that point the numbers get ugly in a hurry.
I’d also walk away from one with repeated loss-of-propulsion or no-start history and no paper trail showing what was repaired. That kind of missing history is a problem on any car. On this one, it’s worse, because the difference between a harness issue and a damaged drive unit is thousands of dollars and a lot of guessing if the records are gone.
A persistent rotational whine during regenerative braking is another one that makes me stop. Maybe it’s still diagnosable to something manageable. Maybe. But I’ve seen enough of these to know that load-sensitive driveline noises on the Volt are not something you casually explain away.
I would not automatically run from a car with a front axle click, because that can be the washer issue covered by 19-NA-103. That’s the sort of thing that sounds worse than it is. But I would absolutely make sure that’s all it is. This is where buyers get into trouble—they hear one symptom, read one forum thread, and decide the whole drivetrain is junk or totally fine. Neither is smart.
If the car has hybrid warning history, no records, a current driveline noise, and a seller who keeps saying “it just needs a reset,” I’m out. Life is short.
Ownership Reality
Here’s the honest version. OEM messaging and real-world ownership are not always on the same page with this car.
The Volt gets talked about like it barely needs anything because it doesn’t have a conventional automatic and because hybrids have a reputation for low maintenance. That’s only half true. Day to day, yes, these can be pretty low drama. When the 5ET50 stays healthy, the car is smooth, efficient, and easy to live with. When it develops internal faults, the bill can feel ridiculous compared with what most people expect from a used compact Chevy.
| Area | OEM Guidance or Official Pattern | Real-World Outcome | Cost Consequence |
|---|---|---|---|
| Transmission design | Integrated electric drive unit with normal multi-mode operation | Some owners mistake normal operating transitions for faults, while real internal faults show up through code patterns | Misdiagnosis can waste diagnostic money or delay needed repair |
| Internal no-start or propulsion-loss faults | Official bulletins direct diagnosis toward internal harness faults and motor-related issues | Cars can present as intermittent electrical problems even though the repair requires internal transmission work | Repair decisions often jump from minor expectations to four-figure bills |
| Noise complaints | Official bulletins separate true internal drive-unit noise from mount-related noise and axle click conditions | General repair shops can overcall or undercall the problem without Volt-specific bulletin knowledge | False transmission condemnation can be expensive; missed internal damage can be worse |
| Warranty timing | Some driveline issues are manageable if found during coverage periods | Many used examples are now deep into post-warranty mileage | Owners absorb the full cost of major drive-unit work |
| Maintenance expectations | This platform is often viewed as low-maintenance because it lacks a conventional automatic | Hybrid transaxle diagnosis is specialized and not every shop is equipped for it | Inspection and diagnostic quality matter more than on a basic compact car |
In real service bays, that last point is huge. A general repair shop can be great at brakes, suspension, and engine work and still be way out of its depth on a Volt driveline complaint. Then the owner gets half-diagnosed, parts get thrown at it, and now the car has a history full of guesses.
I’m also a big believer in records on these. Not because paperwork is glamorous. Because it tells you whether the car had repeat propulsion issues, whether the same fault came back after a repair, and whether a prior owner was chasing the problem with cheap guesses instead of a real diagnostic path.
The ownership reality is simple. Healthy 5ET50 cars are good. Sick ones get expensive fast. There isn’t much middle ground once the internal fault path starts showing itself.
Lawsuits, Complaints & Regulatory History
I do not see a verified transmission-specific class action or a transmission-specific NHTSA safety recall for the 2016–2019 Volt drive unit in the official material reviewed. So if somebody says there was a broad official recall on the tranny itself, that does not line up with the primary source material I worked from.
What does exist is a clear service-publication trail. That trail matters more here than a lawsuit headline would. GM’s own bulletins map out the common driveline trouble spots better than any rumor mill does.
The core publications are these:
- 19-NA-211 for no-start or loss of propulsion with P0A45 or P1B04
- 18-NA-186 for no-start or loss of propulsion with P0A3F or P1B03
- PIC6244C for the internal drive-unit code cluster that points to replacement
- 19-NA-103 for the front axle anti-click washer issue
- 19-NA-067 for regenerative-braking noise tied to debris in the rear powertrain mount area
That’s the regulatory-service picture owners should care about. First, check the VIN in the NHTSA recall system to see whether any open safety campaign exists. Second, and this is just as important, have a Chevrolet dealer or a shop that knows these cars check service history tied to bulletin-related work. A car can pass a recall search and still have a rough driveline past.
I’ve seen that confuse buyers more than once. They run the VIN, find no open recall, and assume the transmission is in the clear. Wrong mindset. On this platform, the service record is where the real story often lives.
Complaint clustering still matters even without a recall. If the same model keeps showing propulsion warnings, no-start conditions, internal code patterns, and drive-unit replacement guidance in OEM bulletins, that tells you where the weak spots are. You don’t need a courtroom to tell you that.
As of 2026, I’d still treat documented service history and a proper hybrid scan as more valuable than broad internet chatter when evaluating one of these cars.
Bottom Line
The second-generation Chevrolet Volt is not some automatic-transmission train wreck. It also isn’t a car I’d buy blind.
The 5ET50 is a clever, over-engineered little unit that works well when it’s healthy. The official GM bulletin history points to the real danger zones: internal harness faults, motor-position fault paths, internal drive-unit code clusters, bearing-related noise, and the separate front axle click issue that can send people down the wrong path.
In my experience, the smartest buyers focus on three things—scan data, service records, and symptom quality. Not hype. Not seller promises. Not “it drove fine for me.” A Volt with a clean module history, no propulsion warnings, no regen whine, and documented repair work is one thing. A Volt with intermittent no-start events, missing records, and a mystery driveline noise is something else entirely.
For current owners, early detection is everything. Don’t ignore propulsion warnings. Don’t ignore no-start events. Don’t ignore a rotational noise that changes under regenerative braking. Those are the kinds of clues that separate a manageable repair from a drive unit full of shavings and a brutal estimate.
For used shoppers, the answer is simple. Verify the VIN. Verify the records. Verify the codes. If the car checks out, this drivetrain can be solid. If it doesn’t, the tranny bill can get ugly fast, and no amount of wishful thinking will save it.
